Anole hot runner system is the injection moulding hot runner ,hot runner installation for hot runner mould.This artile will introuduce the Installation for hot runner mould.

1).Check the mould design match to the drawing.sarying the nozzle sealing surface and the nozzle installation benchmark.put in to the mould carefully.After confirm the nozzle oufit in place,take out the nozzle,check the nozzle sealing surface whether in position.Such as bad cooperation or not in the position to find reasons.If it is good,put the nozzle into mould ordinally and confirm with nozzle in place,then use depth indicator measure the nozzle height higher
 than the nozzle mold A plate(the general standard is 10 cm-12 mm)

2) insert center location pins,check turns positioning pin, center pad is, then put in hot runner on the sealing face "O" type ring slot.

3) installed with screws (shunt board,lock shunt board), confined pad is, hot runner shunt board thermocouples.

4) to facilitate the wiring,the power supply will lead wire, hot runner thermocouple heating circle lead wire,with number pipes to mark.

5) after the completion of the assembly,with depth indicator measuring pressure pad is whether with the height of manifold is the same.(the general standard is higher than the bedding block mould plate 10 to 20), confirm the back cover mould plate height and lock screw cover plate.

6) wiring: the power into the slot and line pressing board their fixed, cuts off redundant lines,embedded φ2-3 wiring head. Confirm connectors: HOUTUR standard for the power cord by male connectors,hot runner thermocouple meet female connectors.

7) field wiring is usually have two kinds of situations:one according to the hot runner connection mode of access connectors.Another provide according to the customer the connection mode of access connectors.

8) after the wiring and connectors in the junction box and fixed in the mold.

9) after the completion of the assembly with a multimeter detection (hot runner heater and thermocouple) resistance and insulating value is normal or not.

Hot runner installation,hope this file can help you know more abou the hot runner knowledge.
 

written by Tina
service1003@anole-hot-runner.com

This article will talk about hot runner function,hot runner advantege in injection mould moulding hot runner,Anole,famous hot runner for mould brand and hot runner supplier in china.

In injection molding process,hot runner used with mould,play an important role.For example,in the production of plastic injection ultra-thin parts (such as the cell phone battery cover),through the use of hot runner can easily produce high precision,high quality products;For the poor liquidity injection molding materials (such as LCP),through the use of hot runner can obviously improve the liquidity of raw materials,ensure injection production running smoothly;For some large injection molded parts,such as car bumper and door plank,TV shell,air conditioning hull,after,through the use of hot runner,make very difficult molding become relatively simple.

In many of cavity mould injection,lack of hot runner simply cannot be forming.That is hot runner is the best technology to ensure the flow balance.In many of the mould cavity injection,lack of hot runner simply cannot be forming.Hot runner is to ensure that the best technology flow balance.Because plastic in port in shear force,no matter how reasonable the geometry of the mould has balance,the products forming out of is difficult to consistent weight,especially concerned for many of the mould cavity is,if do not use hot runner,the products ouside forming out will be lighter than the inside.

To the plastic processing manufacture,as long as there is a certain batch injection production,using hot runner is economical.Because hot runner technology help enterprice deduce the waste material in injection moulding production.In most case,waste material can not used for recycle.Some times the waste material weight is equal to producets.If adop traditional injection type,it mean that the waste material is as manfg as the products.Valuing,use hot runner,can save 30% ~ 50% of raw materials.In addition,would help reduce the wear and tear of mould,extend the service life of mould.Generally speaking,hot runner service life is twice times longer than small gate mould.